I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hello,
A quick question about using an nrf9160 (+ sdk 2.5 - modem 1.3.5)
When I activate the following parameters: # LTE-M (LTE-CatM1) CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_NETWORK_MODE_LTE_M_GPS...
Hey,
I have been using the FOTA download client library with bg95 module for HTTP dfu for a while and works perfectly fine.
Now that I have added a few additions to my...
Hi,
I developed a custom board with nRF52810. Here is my schematic:
Layout:
I can succesfully upload the "ble_app_beacon" example in SDK17.1.0 with softdevice112...
Hello everyone, I hope you can guide me in a right direction. 1. I setup my environment as per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html , using...
Dear support i have two problems,
In ncs 2.6.1 i get: error: '__device_dts_ord_DT_N_NODELABEL_red_led_P_gpios_IDX_0_PH_ORD' undeclared here (not in a function) in the...
Hi All.
I am trying to emulate a central BLE module to scan peripherals around, using an nRF52840 USB dongle and nRF Connect for Desktop. The goal is to confirm that my...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
Hi,
I'm trying to implement a Firmware Erase and Update procedure using the nRF52832 module on a custom board. In the Nordic Devzone I've been following the steps to do...
We are currently implementing the 9151 SIP into our design, and we am noticing some discrepancies between the datasheet and the evkit schematic. I am hoping you can help us...
Hi Nordic team!
Is there any way to dynamically change the charging current while the charging is ongoing? BCHGISETMSB and BCHGISETLSB can be changed only if charging is...
Hello,
We have an nrf522840 board using retained memory feature following this sample and using the NRF_RETENTION setting:
https://github.com/zephyrproject-rtos/zephyr...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi, Goal: Send a firmware update from nrf5340 to another nrf5340 over BLE I found the following sample and a lot of support tickets talking about this sample but I am unable...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
