nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
Is it possible to get a more detailed description of the GPIO block than what is available in the reference manual? Specifically i'm interested in how the disconnect...
Hello Everyone,
I want to run a couple of test on the nRF51422 radio. However, how do I go about checking the firmware on these devices without the use of a motherboard...
Our device fetches fused quaternion from MPU and transmits via NRF 51822.we are using 3.7v li-ion battery.we are using Non-volatile memory.
Currently we are facing these...
I am trying to run BLE central peripheral dual role on nrf52 pca10040 with nrf_uart as service. Also, I have redbearlab BLE nano as peripheral (nrf51822 based).
I am getting...
Hi, I would like to ask that, whenever I put my function in main.c, the borad become undiscoverable.
I'm using nRF51 with ble_app_uart_s110_pca10028, and below are my function...
use nRF Toolbox APP to bonded peripheral device even disconnect and connect don't need input PIN code again, but when I turn off BT the APP lost bond information. next time...
Can the S120 work without RTC XTAL?
Iam using SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION, false);
but it still hangs in the softdevice_handler_init...
Hello,
I am attempting to implement the TWI drivers from the SDK for a nrf52832 chip for a pca10040 board. I am using the twi_hw_master files to drive my TWI and insofar...
Hello.
Since i migrated from 1 to 2 SPI bus, IRQ Handler at completion is not called. Can I use 2 easy DMA SPI ?
1 bus was working fine.
here is my config
/* SPI...
Hello Nordevzone:
8.0 multilink example
I tried to use this modified handler to receive notification data from a s110 based application. The centerpiece of the handler...
Hello! I have been playing with this example and got some LEDs blink here and there, but would very much like to have UART working as well. The documentation states that ...
Hi,
I'm using the nRF51822 for a beacon and following the ble_app_beacon example (SDK 8.0.0) with some modification in order to measure the battery level through the ADC...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Hi,
I have some questions regarding connecting multiple (as many as possible) BLE peripheral devices to a single central (simultaneously).
1:
Does anyone know of any...
