Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hello, I read an article on Nordic site about the Blend Micro:
*"The Blend and Blend Micro also natively support (with no extra wiring) all Nordic Semiconductor nRF8001...
Hi,
I have a few questions on how to receive data (from an iPhone app) as a a peripheral device on nrf8001 (with RedBearLab BLE shield).
Basically I am trying to receive...
Hi,
how do you use the jlink gdb server?
All i get is Target halted (PC = 0xFFFFFFFE),
gdb will obviously not show any helpful trace for that and continue doesn't work...
Dear Nordic guy,
I 'm developing LG product with nrf51822 chip.
I have some question.
Applcation SW timer use the rtc1 clock source.so,
When NRF_timer interrupt expired...
Hi, I'm attempting to use API 2.1.3 and am experiencing some weird issues with transmission intervals. When I use UpdateConnectionParameters to set a connection interval of...
Hi,
I want to upload a firmware using DFU mode.
If I use toolbox 1.8 app of android I can upload the new firm, but If I use toolbox on my iphone, when I push upload the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Dear Sir,
In SDK5.2.0 S310 HRM example, one nRF51422 act as BLE and ANT RX character.
Another nRF51422 with S210 software act as ANT TX character to send out command...
Hello all,
I want to do current measurement for nrf51822 which is flashed with my own ble application which uses some custom services. As mentioned in evaluation kit user...
Hello,
My team and I are trying to decide how to power the nrf51822. We will be using a 3.7V lithium ion battery as our power source.
I saw in another post that it is...
I am planning to use the LPCOMP in conjunction with an external reference. I would like to just use a voltage divider to create the external reference.
Are there any impedance...
I recently received a nrf51822 mbed board.
I went with the mbed board over the EK because I figured it was more 'open', without realizing exactly what mbed was. I played...
I use the SPI slave function on 51422. When I send a byte(0x31) to 51422 SPI slave from master, 51422 will back a byte (0xAA - DEF byte) to master. Why?
I send 0x31 every...
