Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hi,
I am currently working with the channel_sounding/connected_cs sample for nrf54l15 and I keep getting the error: Not enough memory to store step data (530 > 512). I tried...
Hi everyone,
we are trying to use the TWI interface of the nRF52832 to communicate with a TI BQ28Z610 fuel gauge, using the TWI driver of the nRF5_SDK_13.0.
For the last...
This sounds like a stupid question... but I would like to clarify if this pin is an input or output. I think it's power in but want to make 100% sure as I'm spinning a PCB...
Hi , am working on nrf52840 .with nrf desktop v2.9.1 . I am working on display ST7789V with the nrf52840 using Zephyr. I have integrated overlay file . while working on it...
I am having an issue with the nrfx_qdec driver in zephyr, I am trying to simply detect when the turn happens and the direction of the turn is. Most of the time this is triggered...
Hi,
I'm trying to run the Lesson 4 Exercise 2 solution from the Nordic DevAcademy BLE Fudamentals course (origin/v2.9.0-v2.7.0) run on a nRF54L15 PDK board.
I'm currently...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello all,
I am having issues with the configuration of the FEM nRF21540 on the costum board Fanstel BT840NE with the Enhanced ShockBurst (ESB) protocole.
We are not able...
Hi team, According to this statement, it indicates that access port protection can be deactivated by modifying the TAMPC.PROTECT registers, which can be achieved by executing...
I am trying to follow the first lesson of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals
But I have several problems and I can not find out how to fix...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
I am trying to add Coded Phy to my Zephyr BLE Mesh project. I know this is not officially supported, however is possible. Running the stock BLE Mesh Zephyr sample, I keep...
I have an nRF5340 DK that exhibits unusual power behavior. When I plug in the IMCU USB port (USB connected to onboard debugger), the board briefly flashes all LEDs , including...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
