to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
I'm pulling my hair out here. Why would syntax errors completely break the toolchain?
Every now and then ill have a syntax error which causes the build to fail, the entire...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hello-
I'm working on our design for the nrf9160 and I've been trying to wrap my head around the FCC certification. I know that the nrf9160 is an FCC certified module and...
I am developing a project in which a weight analog data is converted as digital by Aviva HX711.
In the host board NRF52840DK, I want to read the wight value.
I have attached...
Hello, I am new to BLE and nrf zephyr programming. I am trying to flash periodic_adv and periodic_sync samples ( https://github.com/nrfconnect/sdk-zephyr/tree/16bcaed54230e3d86aeaf2b2f1d47393967254fd...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
As the poster above mentioned, the nRF54L15 ENGA version is stuck when initializing the GRTC.
it gets stuck at nrfy_grtc_sys_counter_start().
The SDK is 3.0.2.
Is there...
We are developing a BLE application with nRF52833 512kB ROM size and using NCS v3.0.2. However it seems the ROM size occupied is not so logical, or the ROM size for NCS (Zephyr...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...