I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
I am using the nRF54L15 on a custom board where I have good control and knowledge about what is going on regarding current consumption. I am using an MX25R64 external flash...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
I am currently developing a project using the nRF51822 with SoftDevice S110 v8.0.3 in Keil uVision.
To properly manage RTE components and dependencies, I need to use the...
Hi
In my ble repeater application on nRF52833, when I adding OTA function , I found the my image rom size too large to adding FOTA with MCUBoot. there is my memory report...
Hi,
I am currently implementing an E-Ink display application using the SPI interface on our custom nRF54L15 board. I initially configured the display with the following...
Hi All,
I'm currently working with a custom board using the NPM1300 and STM32L4, alongside the npmx drivers. I'm trying to capture both pressed and released events from...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hi,
After some difficulty in obtaining the modem trace file, I'm here to have help about connectivity issue. I have a custom board build with an nRF9151, I use Onomondo...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
