Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
Hi:
I can't compile the program.
Please tell me the solution.
I used with Toolchain&SDK: 3.0.2&3.0.2; 3.0.0&3.0.0 and 2.8.0&2.8.0.
VS Code Winwdows 11, Processor 11th...
Hi, I'm working on provisioning a Pre-Shared Key (PSK) during manufacturing for an nRF5340 device. The device needs access to the PSK at runtime to generate authentication...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello everyone,
I am currently working on implementing the flash protection feature for the 54L05 chip. My objective is to safeguard the code storage area from unintended...
I get a bunch of errors like undefined reference to `mbedtls_ssl_free', `mbedtls_ssl_get_bytes_avail',`mbedtls_ssl_config_free', 'mbedtls_ssl_read'
`mbedtls_ssl_set_bio...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hello,
I am trying to send and receive data from an external slave sensor using the NRF5340. For debugging purposes, I have connected the NRF5340 to my PC via UART.
...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
Hi Nordic team,
I’m working on a custom LoRa interface using the Thingy:91X, and I’d like to know whether the Qwiic connector pins (P0.03 – SDA, and P0.04 – SCL) can be...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hello, I'm developing with an nRF54L15 Revision 1 (QFAA-B00). I'm encountering a problem described in the errata: 3.4 [8] SPIM: Wrong data is transmitted on MOSI (Symptom...
