I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi All,
From the data sheet nrf51822 have a aes hw modules which is used bt softdevice s110.
If i disable the pairing key .
Can I use the inbuilt aes module from...
I am using DEVICEID as an identifier (I know it's not necessarily unique) but when I break the two 32-bit numbers out into bytes, I am finding that the three most-significant...
Hi Nordic, I'm following a guide on this link hrm . I was testing the application with Master Control Panel 3.7.1 with my nRF Development Kit PCA10028. I looked up some of...
We all know we can send acknowledged data in Ant channel.
But based on my test. the acknowledgement message coming back to the originating device is just a dumb packet...
Hi,
I'm new to coding on this platform and i'm having issues. I have an ADXL335 acc sensor connected to P0.04, P0.05 and P0.06 of my NRF51822 (on a custom board). Please...
I cannot get uVision to recognize the J-Link OB device on my nRF51 Eval board. uVision DOES work with a different J-Link OB eval board targeting the same device, the Rigado...
Hi there
I was wondering if anyone has any information or a simple step by step guide for getting up and running on IAR with sdk 7.2 and IAR workbench?
Hi all,
I'm building an application for IOS & Red bear lab BLE shield and Arduino. The phone acts as a remote control for a toy car that I built . It works decently, but...
I'm having problems with a NRF51822 on a custom PCB. I've managed to get the SDK BLE samples working, HRS using Keil, JLink.
I was developing my solution with a MBED kit...
Hello support team,
Iam unable to install nRFGo studio version nrfgostudio_win-64_1.17.1_installer on windows 7 Home Premium 64 bit
The error is " The installation package...
Something did change in the last 2 days but I dont know what.
On tuesday I was able to connect with my mobile device to the nRF51-DK. The application worked fine and it...
I'm using SDK 7.1, PCA10028 and SD310 v2.0.1
Is there a project that implements OOB protection for bonding?
My device has no display, and a single button for input....
I'm getting Error 7 too few arguments to function 'lib_aci_set_local_data' C:\Users\nishant\Documents\Atmel Studio\6.2\ATmega_AdafruitLIB_nRF8001\ATmega_adafruitLIB_nRF8001...
Hello,
as far as I found out, a Peripheral that advertises will stop advertising as soon as it receives an incoming connection (BLE_GAP_EVT_CONNECTED). A central will however...
I'm using the nrf51822 with the IoT softdevice and SDK as an IPv6/6LoWPAN peripheral and Linux with a BLE dongle in the central role. Basically, I have everything working...