I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello everybody!
I have a problem with compilers for nRF51822.
My problems: I create a pwm signal ~38Khz, duty 30% at pin 30 of nRF51822. This process is work well. I...
hi i m using nrf52 with a pi and the gatttool. pi as master and nrf52 as slave. i want to change the mtu but i got no answer from the nrf52 as you see in the log! do i have...
Hello, I have project to do, but I have too less knowledge about NRF's, I've tried almost all information sources and libraries, but no results. I have to make, that one PIC...
I lost many time and check 3 examples for various versions SDK, in all cases device can t connect to smartphone. Check with appl. "nRF UART 2.0" and last "nRF Connect". Applications...
I've spent the better part of a day trying to get the UART demo to work and I'm not having a lot of success. I did get it to connect and transmit data once - I think that...
Just noticed through some experimentation that the SD 7.1 Stack rejects Non-Connectable Advertising Parameters if the interval is less than 152.5msec? Error: NRF_ERROR_INVALID_PARAM...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I am developing a wireless sensor network to exchange body movement acceleration data with one Master and several Slaves. In the developing phase I am using the...
Why would sd_ble_gatts_characteristic_add() suddenly return NRF_ERROR_NOT_SUPPORTED?
It is not a documented return.
It happens only when adding a device information...
Hello,
I want to implement BLE central for Health Thermometer Service using nRF51822 with S130 SD
I used the example ble_app_hrs_c as a reference, but I don't see an...
I have a strange behavior with the Timers. For my project I use a Raytac module with a nRF52 Chip on it. Softdevice is not flashed. Project is based on SDK 11.0
When I...
My setup:
NRF52DK;
Keil 5.22.0.0;
nRF5_SDK_12.2.0;
S132 3.1.0
While trying to use ble_peripheral\ble_app_template\pca10040\s132\arm5_no_packs I decided to modify...
