Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I found we have to build micro-ecc.lib on our own, so I follow the below link to start to build it:
Installing micro-ecc
Then, we meet the below to errors:
Makefile...
Im based in the example of SDK12.0 - MULTILINK_CENTRAL and i have to know the RRSI value in dbm if it is possible from the peripheral device that is connected to me but i...
nrf52 restart from main() after hit breakpoint and enter [Go] under IAR. It looks like there is some kind timer or watchdog to reset system etc... if stay in breakpoint (...
I have a PMIC in the device that I am building which will eventually take over from the battery. But I have to program the PMIC on startup, using the nRF52. I am trying to...
Hi,
It's the first time I'm developing a piece of code using Nordic SDK, so my question may be absolutely dumb!
We are working on a bl652 (with a nrf52 inside). I just...
I have an application that uses many TWI buses, on many pins of the nRF51. I handle this by initializing/uninitializing a single TWI bus for different transactions. I ran...
in S130 v2.0.0, what is address of central?
i'm using ble central tutorial successfully compiled.
in case of ble peripheral, i can set address whenever running.
so ble...
Dear Nordic Team,
Thanks for supporting.
How to add custom characteristics in standard service ?. I am using Health Thermometer service (HTS). I want to add two custom...
I mounted the chip onto my own PCB, I am not using a devkit, My board is "Wireless-Tag WT51822-S2", it is a module that uses nRF51822-QFAA as (SoC)
I am the ble_app_uart...
With the release of SDK 12.1 the Serialization of S130 is now deprecated.
Within SDK 12.0 the Serialization was supported NOT at all.
When this is true, I have to stay...
I'm trying to stream data in real time from 4 different sensor units to my computer. Each of these sensor units has an NRF52 module that sends data at 50 packets per second...
Hello, I'm south korea student in dongguk univ.
and i want to know how can i send the message on my board(not use the terminal ).
I use the keil uvision4.0, nrf51822...
Hi,
I want to change eddystone_url_data parameter in experimental_ble_app_eddystone (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples\10.0.0\ble_peripheral\experimental_ble_app_eddystone...
