Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
I'm running app_error_handler with
SEGGER_RTT_printf(0,"\nerr_code %d on line %d file %d",error_code,line_num, p_file_name);
to print out what went wrong and where...
We are writing an Android app for our own peripheral (nRF51-based). We know the handles for all the characteristics.
On Android gatt.discoverServices() needs to be called...
I've tried to use UART samples to test large BLE payload size with SDK 12 and SoftDevice 3.0
What I did is modifying UART central and peripheral code:
In both project...
Hi,
I have an nRF51 project using SD110 and SDK8.0 that refuses connection parameter negotiation. I a handler that would disconnect bluetooth when a connection parameter...
If, for example we would source 10 mA on 2 pins (2 x 5 mA), how much current can we sink on high drive pins?
Is that 15 mA overall sinking and sourcing (which seems like...
Hi,
HW:PCA10040
SDK:v12.0
QUESTION:PWM
I want to use SDK 12 to get 4 pwm , so i search in pwm , i start my program like this , but i can't find nrf_drv_pwm_config_t...
anybody knows how to download the nrf52 sdk common library document?
i only find a online help infocenter.nordicsemi.com/index.jsp but i need a offline reference manual....
Hi, I am using following code inside for(;;) in main function
if(diff == 30)
advertising_stop();
else if(diff == 60)
advertising_start();
Following are the advertising_start...
I use IAR to debug nRF51_SDK12.0.0 ble_app_uart example application. The origin application is for nrf51422, and my device use nrf51822. Therefore, I first change the device...
I'm using a S130 on nrf51822.
connect to 3 peripherals (in case of the master)
connect to 1 central (in case of the slave)
But, I want to use 1 peripheral and 1 centeral...
I'm using nRF52+SDK11.0.0+S132 with an application based on the ble_hrs example.
In main() , if I call a blocking nrf_drv_spi_transfer() to configure some SPI sensors before...
Hello I tried to do a application update with my own key and it does work.
But then I tried to create zip with all 3 parts: APP+BL+SD (application+BootLoader+SoftDevice...
Hi
With the introduction of softdevice v2.0.1, the connection bandwidth has become configurable to be low, medium, or high; and can be specified independently for TX And...
Hi,
Now I'm using nRF52 SDK v12 and S132, I have some data(about 300 bytes)need to write to the flash. I have seen the fstorage but I donn't know how to use it. Could anyone...
