I 've been working with the nRF54L15 for a bit now and it' s been great, but trying to get a bit fancy now and running into problems. I 'm developing with the latest NCS v3...
Hi.
I'm using nrf Connect SDK v3.0.1 and Zephyr v4.0.99 to implement a IoT device which connects to a Thingsboard server with CoAP. With the COAP_CLIENT Lib I want to download...
Hello,
I am testing the RF range of a BLE application based on PAwR (Periodic Advertsing with response) in coded PHY (S8) with SDK 2.9.0.
In order to test the robustness...
Hi all, hope this is the right place. I'm developing a small breakout board to test/program the NRF52805; this board will eventually be expanded to include a pressure sensor...
Hi
I can run the sample application for NVS, on the nF5340 DK (SDK 2.9.0)
I can run the sample application for LittleFS, also on the nRF5340 DK
Now I would like to see...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Hello.
After some great struggles, we've managed to enable WiFi and encrypted socket + TLS connection to google.com and various websites.
Since then, we've been looking...
In SDK source code of S110 SOftdevice, I'v found two events for which module is registered and waiting using "softdevice_sys_evt_handler_set" & "softdevice_ble_evt_handler_set...
Hi,
I'm working on getting our product through BLE certification and they are asking a few quesion's that I'm not sure about.
1: Pairing. Is it using a fixed PIN or...
Hi,
Routine running normally in low power mode with power_manage() .
but after sd_flash_write/erase current consumption goes high(almost 20mA).
If anything is missing...
Hello,
i want to update the softdevice S310 V1.0.0 to version V2.0.1. My applicatio based on SDK 6.1. With S310 V1.0.0 all works fine. But i can't update to S310 V2.0.1...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello, I have a problem with GPIO Input control
My sensor work on special clock generated by MCU
I've controlled this sensor by Arduino like this
//SCK digital pin...
We are using the NR51422 to develop a BLE application. We reused the project “ble_app_hrm” from the SDK v6 and ran it using the NRF6310 board, everything is ok.
We just...
Hello Everyone, right now i use nrf51-dev kit and i want blinky code for that, in Keil i compile code and load in kit and it work fine but now i want to make code in eclipse...
I'm trying to debug the blinky example with SDK 7.1 using Eclipse Luna. Going through several threads here I could figure out configurations needed and build the app. I can...
Hi,
I have been trying to study how to implement support for over-the-air (OTA) updates in my current S110-based project. But I'm already stuck in the very beginning. How...
I am using softdevice and RTX at the same time.
RTX is using RTC1, softdevice is using RTC0, so no problem there.
But sd_softdevice_enable require a clock source as one...
Hi,
I have problem with nRF51 antenna orientation. I used nRF51 developement kit (mKIT) board and I had problem with communication if I just change a little inorientation...
Can I change the shared channel address (first one or first two bytes in the message) when the channel is open?
The manual says after opening the channel, send a broadcast...
