Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
Greetings,
I'm experimenting with iOS and bluetooth, using the Heart Rate Monitor example. I have tried, and failed, to convert the NSData I get from the "Heart Rate" characteristic...
In one of my current projects, I need:
to have access to more than 8 kB of RAM (which is not possible when using SoftDevice)
to have Observer role (which apparently...
I see many questions regarding developing applications without the SoftDevice. Perhaps I don't understand how this firmware system works, but isnt the SoftDevice required...
I am new to Bluetooth 4.0 and want to use for a specific application. I intend to modify the Bluetooth 4.0 protocol and would need continuous transmission of packets. Is it...
hiii....
i am using lightblue app in i phone to connect with the advertising device...in my ble profyl i have 5 services and 5 characteristics in each... most of dem i...
I make a call to sd_ble_gatts_hvx, and get an error. The call produces an error and I end up in ble_debug_assert_handler
From ble_debug_assert_handler:
The file name is...
Hi,
I've tried to implement s120 softdevice (version 1.0.0 production ready) on NRF51822 Development Kit and run ble_app_multilink_central example from sdk 6.1.0 on it but...
My devices should be able to "see" each other and at the same time they should be able to extract some information from a received Advertising packet. After reading about...
Hi, I use s120 stack. Peripheral device sends a notification 6 in a row, but the central device receives only the first 3 notification. How to get all the notifications?
Hi,
I have 2 pins with PULL_UP in sense mode and when i use sd_power_system_off() i measure 25mA current, which is higher than when my system is on (around 10mA)!!
How...
We are using an nRF8001 with bonding. We are trying to figure out how big the dynamic data is that we need to store (since we are used a fixed-size storage in flash memory...
I just received my Beacon Kit and need a programmer/debugger but money is tight. These are the options I'm looking at:
cut the traces on my nRF51822 EK board and add...
I wrote an application that works using an Enhanced Shockburst-compatible protocol (because I need it so), using the RADIO interface.
What happens if a packet with an address...
Hi U guys
First I’m pretty new I use of bluetooth low energy, so bear with me.
It is pretty simple, I need to send a temperature each 10 sec. or whenever it has changed...
