We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
Hi,
We want to evaluate the Bluetooth: nRF Distance Measurement with Bluetooth LE discovery functionality. But we only have nRF5340 Audio DKs. Not ordinary nRF5340 DKs...
Hi,
My project is based on NRF52832 with SDK11.
I got 2 working units, 1 is advertiser and 1 central.
The advertiser is advertising every 2 second.
The central unit...
Hi Nordic team, 您好，北欧团队，
I am developing nrf54L05 in VS code with NCS.I want to configure the SEGGER_RTT_printf to my project.Is it correct to change the CMakeLists.txt...
Hello, I am trying to develop a bluetooth mesh network with two provisioners, one being an external provisioner (mobile phone) and another being node in the network (nrf5340...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
Hi everyone,
I'm developing a matter generic switch and I’ve run into a puzzling behavior when commissioning an nRF52840 DK with Apple Home via an Apple TV Thread border...
Hi, I am using nrf52840 , nrf connect sdk 2.6.0 I am using spi_transceive() to send and receive the data from sensor I read in Nordic Academy nrf connect sdk intermediate...
I use SDKv2 . 09 . 00 without using the eSB function timelot can trigger MPSL_TIMESLOT_SIGNAL_TIMER0 normally，then NRF54L15 Running esb and BT at the same time with MSPL cannot...
