Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I have designed and built a custom nRF52840 board and I’m experiencing difficulties programming it via SWD using an nRF52840 DK (version 2.0.1). When I connect my custom board...
Hi,
I am struggling a bit on how to correctly extract the device name of the reflector, which is present in the Advertisement Data.
The code that i have down below shows...
Hello
Following my previous message from yesterday, the service seems to no longer be usable again at the moment.
Could you please confirm that this is a temporary issue...
How is it possible to read the DEVICEID from the FICR for any Nordic family device in a generic way using nrfutil?
`nrfutil --json-pretty device device-info` does not include...
Hi,
I use the nRF9160 with SDK2.5.0.
Which MQTT version (3.1, 3.1.1 and 5.0) does it support? And w hich QoS level (0, 1 and 2) does it support?
Does it support QUIC...
Hi, Looked into public Nordic repositories in github looking for a recommended implementation of CTS (current time service) to use with this sample: https://docs.nordicsemi...
Hi,
I've got a question regarding the configuration I have to make in order to get the logs from the nrf9160 in the serial terminal using the hci_lpuart sample.
My setup...
I have been using a Chinese debugger ARM v9 which supports JTAG+SWD to debug my nrf52840dongle so that I can upload my custom bootloader with my code in it using SWD pins...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
I want to implement FOTA Update for a nrf5340 based board by using nrfConnect SDK v2.9.0 with zephyr and mcuboot. The board has a MX25R6435F external flash (same as the nrf5340dk...
Hello,
I am trying to run a ztest integration example I found under this one here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/testsuite/integration...
Hi,
I am sending out same payload through ADV packet and BLE connection packet, I notice the ADV consume more power compared to connection one,which is quite strange.
...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
