Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hello,
I am currently experimenting with bonding and I stumbled over the config CONFIG_BT_BONDING_REQUIRED.
Currently the BLE characteristics of my peripheral do not require...
Hi,
I have read the documents regarding the powering up the board form external supply and switch position
i need simple answer how power the board completely means...
Hello Nordic team,
I am trying to use external flash on nRF52840dk using Qspi.
Above is my overlay file.
Above is my pm_static file.
I am using custom board where...
I am trying to send a variety of AT commands to my module and it looks like I am missing something or the documentation is not up to date for some of these:
If I try to...
Good morning,
After updating the VSCode extension "nRF Connect SDK" to version v2024.12.55 , I encountered an issue where the "Build" and "Action" menus do not update after...
The datasheet, page 78, says "Supervisor HW to manage power on reset, brownout, and power fail".
We are powering from a solar cell, so the power supply voltage ramp will...
HI i am using nordic nrf52840 dk(pca10056) . i am using ble_app_uart example code for my development. i have connected usb in j2 but when i keep my power switch in usb adv...
Hi! I want to write some software utilizing OpenThread and CoAP. I've seen samples of coap server and coap client in NCS. However, I want to ask whether it's possible or not...
Hi,
I am currently investigating the possibility of using Nordic nRF52840 as the PAwR advertiser and the other device (from a different vendor) as the PAwR scanner. I don...
nRF 52832 + NCS 2.6.1
We are successfully setting the advertising Tx power in discrete steps {-40, -20, -16, -12, -8, -4, 0, +3, +4}dBm using
However, I am being asked...
hi support team,
customer had one problem about 9151 with esim: the iccid can't be readout, it should be 19 bytes string, but we only get 6
may i ask what could be the...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
I’m using the DECT Shell perf command to evaluate DECT NR+ performance.
Could you please clarify the units and scaling of the snr field in nrf_modem_dect_phy_rx_pcc_status...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
