Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
Hi, last year the name of the Zephyr module "TraceRecorderSource" was changed to "percepio". In January a PR was accepted that updated the SDK's allow-list (west.yml).
We...
Good morning,
In my application (SDK v 2.8.0) I would like to disable/enable runtime the advertising for the mesh provisioning. The inizialization of the mesh stack works...
Hello , I have a problem on angle of arrival application to see switching nrf52833 board
I use nrf52833 dev board. I use 2.0.0 as sdk version. I use nrf/samples/Bluetooth...
I would like to know the recommended battery part that is suggested by nordic to work with the nrf5340 Audio DK. I saw some blogposts where it was mentioned that a 3.7V 1500mah...
Dear nordicsemi,
In our application, we need obtain the number of input edges,but we always get a incorrected result in a long-time testing situation (2-3 hours), and this...
Hi,
I would like your support in reviewing and helping define the correct configuration for the NPM1300 charger in our application.
Here is the current configuration we...
working with a nrf52833, soft device 140.
I am trying to setup a whitelist with a known addresses before I start scanning. I am calling the following code before my main...
I am trying to find the reference manual and specification of the S130 SoftDevice (2.0.1). I can't seem to find it in the info center or the your docs page. Am I missing it...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
Hi,
We recently purchased two Thingy:91X devices and are trying to run the nRF Cloud Multi-Service sample on the nRF9151 SiP onboard. To provision the Thingy:91X for communication...
I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Hello,
I'm trying to evaluate a FW development for several features of BLE used simultaneously. I need a BLE Peripheral for mobile phone connection (advertise only once...
Hello,
I just downloaded nRF connect for Desktop App, and plugged in PCA 10100 2. 0. 0 , 2023, 3.
I ran quick start, and this is what I get.
Any explanation on why...
