Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
Hello,
I have a custom nRF52820 board powered by a coin cell, and I want to measure its power consumption using the Nordic Power Profiler Kit 2 (PPK2).
Could you please...
I met some problems when add build configuration to my first application. I used the blinky sample template. And the device a nRF5340 DK. My PC can detect my devices. But...
Hello everyone,
I'm working on a project based on the nRF52840, and I'm using nRF Connect SDK 2.9.0. The project uses MCUboot, but the firmware image is signed externally...
Hello, I am using NCS 2.9.0, an nRF5340, custom board files (see attached), and no external flash and I would like to use simultaneous DFU over BLE. I believe this should...
Hi,
I'm currently using “light_switch” to enable BLE NUS, but every time the device reboots it needs to be re-paired, I checked the serial logs and found that the pairing...
HI there,
I am using keil pack installer. but found the download link is broken:
" ">developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.40.3.pack...
Hello,
I'm using central_past sample on nrf5340 audio DK board, and select nrf5340dk_nrf5340_cpuapp_ns for Build Target.
I added the following config to enable RTT log...
Hi all,
We are looking to use the nRF9151 and we are trying to determine estimated certification costs for US deployment
So, if anyone can help or knows:
What pre...
I've been using the ppk2 power profiler with version 4.0.1 for over 2 years and it has worked very well in providing a power source and monitoring/ with reviewing the power...
Hi, I'm currently working on adding DFU over UART to my firmware running on an nRF52dk/nrf52832. To have a minimum viable example, I'm trying the DFU over UART exercise sadly...
Hi Support Team,
I met a conflict situation. Could you help give me some guidance?
The project is based on nrf5340 and ncs V2.5.2. The device supports BLE FOTA and works...
Hello,
We've recently updated our BLE-USB bootloader from using SDK v15.2.0 to v17.0.2 and noticed an issue. Our USB-BLE bootloader was created with the USB-serial bootloader...
Hi，I would like to know how it works when reconnecting after a timeout disconnection，I didn‘t find the answer after reading Bluetooth 5.4 specification.
Hello,
I'd like to download the latest MDK for SES - links here appear to go nowhere: https://www.nordicsemi.com/Products/Development-tools/nRF-MDK/Get-Started?lang=en ...
Our design has an nRF5340 with a 32 MHz high frequency crystal and an accurate 32 kHz external rail to rail clock chip (+/- 5 ppm @ 25 C). We would like to measure the actual...
