Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Does the following flasher also allow to debug the nRF51822 device?
Segger Flasher Portable
If not... which flasher/debugger is suitable to be used during development...
I'm adding the bond manager to an existing nRF51822 s110 soft device project to enable encryption when reading/writing certain characteristics of a BLE service.
As far...
i am making something about dfu!
i read some message from "readme.txt"
such as :
Program initial SoftDevice
Make sure the device is cleared (nrfjprog --eraseall...
I have trying my best to find the url of ''nrf51_sdk_v6_0_0_43681.msi'，but there is nothing i got, i need some help.
Do you know somthing about it? thanks!
Edit: One...
Hi,
We're using the SPI to communicate with a device that, when powered up, supports only up to 3Mbps SPI frequency , but after a while can work with higher frequencies....
Hi,
We have a customer requirement that he want to setup the ANCS service bypass pairing. It looks TI CC2541 could do so as below URL. Do you think it could be done from...
Hi. We're looking at nordic modules for a range of new miniaturized health sensors.
Does anyone know how to compute the current consumption of a BLE module given the data...
Hi!
I've quite wired problem with PWM based on NRF_TIMER.
When I modify CC value to adjust current value to desired value slowly (function is fired from outside event...
I have written application similar to ble_app_temp (posted by Ole Morten) and during the test I noticed that current consumption is extremly high. I used brand new coin battery...
I have writable characteristic on the server. As far as I understood there are at least two ways to access to its value: one using ble_evt_t and BLE_GATTS_EVT_WRITE another...
Hello,
i have seen here a extended version of Spi-Master driver:
devzone.nordicsemi.com/.../a00006.html
With funktions like:
-spi_master_send_recv();
spi_master_get_state...
I'm using the reference design for the WLCSP nRF51822 package, and I noticed that there are 2 pins (G3 and G4) that are listed as N.C. (No Connection) in the product specification...
Hi,
I am upgrading SDK from 5.2.0 to 6.0.0 working with SoftDevice 7 and I am facing a problem in relation with ANCS.
When I am pairing the phone (IOS 7) the first time...
