Hello everyone! I'm currently working on a custom PCB designed specifically for drone communication . In my design, I'm using the nRF52820 as the main microcontroller and...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hello everyone,
I am trying to test the SLM on the nRF9160DK on NCS 2.9.0. (SDK and toolchain) I want to control the nRF9160 with an external MCU, so for this the application...
Hello,
Our product that we currently design is based on the nRF52840 QFAA and w e are looking to achieve FCC, CE and RED compliance.
I would like to request any certificates...
Hi,
I'm working with the nRF54L15 SoC and running into an issue when using UARTE21 together with SMP over Bluetooth . Here's what I’ve observed:
UARTE21 works perfectly...
Hi,
I have an issue with nRF Kconfig GUI in VS Code.
My prj.conf is empty, and the _defconfig file of my board contains this:
When I open the GUI and...
I'm trying to get the USB Mass Storage sample working on the nRF52840 using SDK 2.9. I followed the official guide here: https://docs.nordicsemi.com/bundle/ncs-latest/page...
Hi!
I have somehow softbricked my nrf54L15 dk. This happened by using nrf conncet board configurator. First symptom was no uart logs and now I get this crash via RTT logging...
This issue is a follow-up to the previous one: 341132
When upgrading our device from Matter 1.1 to Matter 1.3 firmware via OTA, the MCUBoot program in the old firmware fails...
Hello,
I am conducting a feasibility study on implementing Auracast capabilities using the nRF5340 Audio DK with nRF Connect SDK v2.9.0. My goal is to investigate the potential...
Hi,
Recently, when I tried to obtain Bluetooth certification with nRF52840.
I found that there is a new requirement as shown below
RF:P1 - TRM/CA/03 Power Control
...
Hello,
I'm creating a simple test project based on the l4_e2 example, but I'm having trouble debugging it. The program encounters a fatal error before the main() function...
PPK2 is stuck in bootloader after trying to flash the latest firmware on Power Profiler 4.2.1 (Windows 10).
The error is "serialport could not be opened ". The same issue...
There is an issue i am dealing with while working with ble stack of nrf52810 with nrf connect 2.7.0.
1) memory status of my application without ble:
2) memory status...
I am using nrf52810 with nrf connect 2.7.0.
Is there any provision to update firmware using BLE? If yes is there any official document or article regarding this?