I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
hi i have a question
i ues ncs 2.9.0
This is the code that displays my Bluetooth connection
——————————————————————————————————————————————————
struct bt_data ad[]...
I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hello Team,
I’m working on creating a custom Matter cluster using the instructions provided in the Nordic documentation: https://docs.nordicsemi.com/bundle/ncs-latest/page...
I'm getting the following warning on my terminal during build:
-- Including generated dts.cmake file: D:/Workspaces/azure_iot_hub_9/build_pmi/mcuboot/zephyr/dts.cmake CMake...
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
Hello DevZone,
I have learned that some knowledge about CLOCK. But they are a little bit confusing. I just want to get confirmed by any expert.
1. Some peripherals ...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
NRF52840DK NCS 2.8.0 Hello , We are developing an application where a device with router function must join a coordinator network. The coordinator uses OOB (proprietary IR...
I am working with the WLCSP version part (nRF54L15-CAAA) and it calls out that there is light sensitivity. The note seems to indicate that only underfill around the perimeter...
how to upload modem firmware and and connect to nrf cloud and send modem firmware and asset tracker hex file and procedure to connect to nrf cloud ( i tried and sim activated...
Hello, I searched the forum for similar issues and found a few, such as
I am currently implementing a PSRAM is66wvs4m8 on the Thingy 91 via SPI, using SPIM3.
The problem...
I get the source code from the github.com/.../ncs-fund.git , and trying to build the exercise-1-5 of nrf-connect-sdk-fundamenta lesson-4-serial-communication-uart for 54l15dk...
Hello,
I attempted to follow the nrfutil offline install instructions. However, I keep receiving the following error when trying to install the device package on the remote...
