I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hi,Team,
I'm using the nrf54l15-dk to develop zms to save custom configurations without affecting the pairing information of ble.
So I have a few questions: 1.Is the storage_partition...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
As you can see in the schematic, I have a custom board, and I’m uploading code to it via J-Link. I can control the pins, turn on an LED, and read a button without any problems...
Hi,
I’m trying to understand the following parameters in the nRF54L15 channel sounding configuration, because their function is not clear to me. I added my questions as...
The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
i have PMIC(I2C based )Max20360 that is developed using twi sensor , to this when i am intergrating a SAADC part throws error error # 134 :expected a field name . 1)why am...
Hello all,
I am using the nrf52840 MCU and NCS v2.6.2 for my application development. Here I am using SPIM3. I am using a peripheral which have an internal FIFO. From...