I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, I am a beginer, it is my first time using raw MCU IC, and I don't know how should I connect my 32MHz oscillator. So I see that the nordic configuration looks like this...
Hi,
I’ve compiled and flashed the Matter light bulb example from Nordic onto the nRF5340 DK.
I'm using the nRF52840 Dongle as the OpenThread Border Router, with a Raspberry...
Hello,
I have a custom hardware around the nrf52820, and I simply can't make it to run the basic hello_world and blinky samples.
I'm compiling the samples using nrf52833dk_nrf52820...
Hi,
I've just migrated my project from NCS 2.6.1 to 2.9.0 and I'm having some problems with the UART.
I'm using the nRF52833 DK to communicate with another device and...
Hello,
I want to port blinky example to 52805.
I wrote this dts file:
I added " CONFIG_DEBUG =y" to prj.cong.
I launch debug but main function is never reached...
I discovered weird modem behavior when testing my application with a weak or undetectable signal. Mine testing was as follows:
modem connected to the network
communication...
Can the npm1300 be set up so multiple interrupts trigger the same line, and then the host can determine what the cause is?
Or does each interrupt need a 1:1 correspondence...
We are developing a device that uses BLE, 4 contacts (buttons), a piezo connected via PWM and a realtime clock (RV3028). It also stores event data on an external flash using...
My application communicates via UDP and all communication is initiated from the device. Before packet transmission, network registration status is checked (CEREG) and sendto...
I boot AOK after I do a west flash --erase. But after that, when I try "west debug," I run into this:
*** Booting nRF Connect SDK v2.9.0-2e7ce73f5faf *** *** Using Zephyr...
Hello
I am playing with the mesh dfu and the distributor application on nRF52840 DK board
I load the image I want to distribute using mcumgr application on a Raspberry...
Hello
According to Enhanced ShockBurst (ESB) documentation , to stop the ESB module you need to call esb_disable(), but it also says that you need to check if the module...
Hello,
We are considering to develop an appliance based on the nRF5340 AUDIO DK.
The nRF5340 AUDIO DK contains the VM3011-U1microphone that is absolute on the market....
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
