Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
First, I'm just beginning bluetooth solutions, so I apologize if my question is dumb :)
I have 2 Arduino boards, with 2 nRF8001 shields.
I want to connect them. After...
Chip: NRF51822
Per the documentation the band gap voltage is 1.2V however on my board when I apply the voltage 1.5V to AIN2 i read the following value from the ADC: 209...
I am completing a schematic using the nRF51822 part. I will be supplying the part with a 3.3V supply. I will use one of the ADC inputs to sense battery voltage (up to 10v...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I was using nRF Master Controller app on Samsung S4 to connect to my Ble device. However, after connected a while, the device will be disconnected automatically while I was...
I'm getting started and have an overwhelming amount of stuff downloaded which I'm trying to make sense of.
Which of the examples in the nrf51 SDK use the Softdevice and...
Hi,
I'm using a NRF8001 shield with an Arduino Leonardo, everything connection wise seems to be working. I'm using the "ble_my_project_template" and uploading various services...
I install the j link driver for mac(4.78k),connect the ek,but can't recognition it:
Sens-Macbook:~ sen$ JLinkExe -if SWD -device nRF51822
SEGGER J-Link Commander V4.78k...
I'm usually cleaning out the older manuals when downloading new ones from the web site. Unfortunately the new EK user guide 1.2 doesn't show how to connect the nrf51822 UART...
I would like to use an idle loop for non critical tasks. Is there any way this can be done with the scheduler implementation? I don't want this to be time based, I just want...
I have worked with nrf24l01+ devices. In my project include single PRX with 100 PTX. Objective of this project is all PTX send packet to one common PRX device & PRX send ack...
I have the simple UART example working with the nRFgo motherboard laid out as described in the SDK docs, with 2p connectors on the RS-232 P15 and the SDA and SCL pins of the...
Hi All,
I'm just starting to use the 51422 DK and I do as the nRF51422_Developer_Kit_User_Guide,I have flashed the broadcast_tx of the ant_broadcast project in SDK and...
After I download NRF51822_0.9.0.HEX in PCA10001 v2.1, but the MCP cannot work. Anyway, PCA10000 is working fine. Do you have any solution about this? Thanks.
