When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
First, I'm just beginning bluetooth solutions, so I apologize if my question is dumb :)
I have 2 Arduino boards, with 2 nRF8001 shields.
I want to connect them. After...
Chip: NRF51822
Per the documentation the band gap voltage is 1.2V however on my board when I apply the voltage 1.5V to AIN2 i read the following value from the ADC: 209...
I am completing a schematic using the nRF51822 part. I will be supplying the part with a 3.3V supply. I will use one of the ADC inputs to sense battery voltage (up to 10v...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I was using nRF Master Controller app on Samsung S4 to connect to my Ble device. However, after connected a while, the device will be disconnected automatically while I was...
I'm getting started and have an overwhelming amount of stuff downloaded which I'm trying to make sense of.
Which of the examples in the nrf51 SDK use the Softdevice and...
Hi,
I'm using a NRF8001 shield with an Arduino Leonardo, everything connection wise seems to be working. I'm using the "ble_my_project_template" and uploading various services...
I install the j link driver for mac(4.78k),connect the ek,but can't recognition it:
Sens-Macbook:~ sen$ JLinkExe -if SWD -device nRF51822
SEGGER J-Link Commander V4.78k...
I'm usually cleaning out the older manuals when downloading new ones from the web site. Unfortunately the new EK user guide 1.2 doesn't show how to connect the nrf51822 UART...
I would like to use an idle loop for non critical tasks. Is there any way this can be done with the scheduler implementation? I don't want this to be time based, I just want...
I have worked with nrf24l01+ devices. In my project include single PRX with 100 PTX. Objective of this project is all PTX send packet to one common PRX device & PRX send ack...
I have the simple UART example working with the nRFgo motherboard laid out as described in the SDK docs, with 2p connectors on the RS-232 P15 and the SDA and SCL pins of the...
Hi All,
I'm just starting to use the 51422 DK and I do as the nRF51422_Developer_Kit_User_Guide,I have flashed the broadcast_tx of the ant_broadcast project in SDK and...
After I download NRF51822_0.9.0.HEX in PCA10001 v2.1, but the MCP cannot work. Anyway, PCA10000 is working fine. Do you have any solution about this? Thanks.
