Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
HI,
I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
EDIT
I think there is somewhere in KEIL or nrf libraries a bad pointer type alignement .
The correct pointer is given as uint_32_t ( NRF_SAADC->RESULT.PTR = (uint32_t...
I notice that each dev board has a version of nrf_drv_config.h in the config folder. For my custom target, I want to create my own version of this file where I will modify...
I use nRF52832 as a master to communicate with ads1292. then I want to config the ads1292, so i should send the register address and configuration data.But I don't know how...
Hi,
I tried to compile my own program with eclipse and GCC with c/c++.
I followed this tutorial : TUTORIAL
I have some problems :
First : i have problem with...
Hello,
I developed a code (softdevice S110 and SDK 10) on a prototype based on a NRF51822G2 chip. I tried to reproduce the prototype with NRF51822H0 chip.
I flashed...
Hi,
I use ESB protocol, and all is working fine :)
Now I want to retreive the address of the sender because I can have multiple sender in my network.
I can add this...
With there being +/- 4dBm variability in output power from nRF52 to nRF52, each device needs to be calibrated in order to comply with FCC rules. One of the rules is there...
Hi
I'm porting a nrf51822 project with S110 to a nrf52 board. In this case, I'm a bit confused about which softdevice to use. S132 it is the equivalent to the S110? Or...
Hello everyone,
I am using the nRF52832 rev 1, i am not using the softcore. When the cache is enabled as below, the performance actually seems to get worse.
F_NVMC-...
using Bluetooth Developer Studio, and
nRF52 SDK v11.0.0 - Experimental: Bluetooth Developer Studio Example
I have created a profile using BDS and generated the files with...
In order to teach a class of students using nRF developer boards I'd like to use the nRF Blinky application running on Android, iOS, or whatever mobile platform. The problem...
