Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi!
I have been trying for over a year to figure this out, but I am unable to, and I would hope it be pretty straight forward since OTA is already in the Nordit Master Control...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a device (configured as a slave) which is connected to a relay to on/off a motor.
Now, I need to connect it to multiple masters (e.g., couple of smartphones) to remotely...
Hello Guys,
I need suggestion regarding the selection of nrf8001 ble module
Does it support OTA updates?
What is communication interface? is it SPI or conventional...
Hi,
I want to discovery all attribute UUIDs as Master Control panel application does. I use API function 'sd_ble_gattc_primary_services_discover' to discovery.
Exactly...
Hi:
I develop my project with gazell, Device can keep send to host,but host can't keep send to device(I'm not mean for host sent ack to device).
In my program, I use "nrf_gzll_add_packet_to_tx_fifo...
In the nRF52 reference design, not using the DC-DC converter would result in higher power consumption. By how much? Any documentation regarding the details. Thanks
Hi all,
I am new in nRF51822. Today I am doing experiment using GPIO and radio transmission.
I wrote a very simple code as below:
int main(void)
{
init_clock();...
Hi, I've got a serious problem in my project. Some of its features require hard timings. The usage time of these features is longer than the single timeslot and I must be...
Hello guys, I'm doing a hobby project and can't seem to get it working. Aim of the project is to transmit temperature values from a DS18B20 using an Arduino Uno and NRF24l01...
I'm experimenting problems with a nRF51822 custom board. Recently I managed to run the blinky sample project. Now I'm trying to test a BLE project, but I'm having problems...
Hey All,
I am currently trying to have a Analog Signal come in through P0.05 which then gets converted via the onboard ADC and send out a Service Characteristic. I am using...
Hi,
I am using your NRF24L01P-R7 part .Can you please specify its maximum distance upto which it can detect other TAG in open area when there is no wind at normal atmospheric...
I have a question about PXP profile. Could I use the nrF52 (S132) Nordic's PXP example to dynamic change TX power when I have bonded or connected Android phone device ? I...
