Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
We're having difficulty preventing our nRF51822 from resetting when ESD events occur. These events are not directly on the nRF51's I/O pins, and we've tried things like grounding...
Hi,
I am having a BLE peripheral on NRF51822 chip.
I have set to MITM to 0.
I want to communicate with an iOS app which will act as central device.
When i first connect...
Hi,
I'm planning to use the nrF51822 in the end product and the nRF51DK kit has nRF51422 and not the nRF51822. the user guide for the kit says that 51422 supports ANT protocol...
I am doing a bootloader to support updates via ESB. I am using MicroLib. I am not using SoftDevice.
My project mapping:
Bootloader 0x0000-0xBFF
Application Vector Table...
I use Keil uVision 4.74.0.22 to compile nRF51-ble-bcast-mesh-master with nrf51_sdk_v6_1_0_b2ec2e6 and get the rbc_mesh_BLE_Gateway.hex. However, I drag and drop the hex file...
The iOS app we have is identifying the device via the name broadcasted and the service UUID. On production devices, are the Service UUIDs on the same product, the same on...
Fisrt of all, I have searched all the questions but now still can't make bond work.
I've done below work:
1, modify main.c file to add device manger function
2, modify...
Hello,
I am using NUS service as a peripheral with read and write characteristics and tested on master control panel.
Now I am using S120 stack for central device and...
Hi,
I have a PCA10028 which has a 51422, and trying to run ble_app_uart_c example on it. But no success. I don't get any thing on COM and LEDs do not turn on at all. Does...
Good morning,
I am using nRF51 SDK v10.0.0 and I have to synchronize access to a hardware resource shared between two control flows. One flow is an interrupt handler invoked...
I just ported my SDK 9.0 app timer code to SDK 10.0 which requires the use of the new APP_TIMER_DEF() macro. The problem is that is generates warnings in Keil (v5.17) that...
I am using nRF51822. I want to know that how to perform file read, delete and write operations. Is there any API available for this. If file operations are not supported by...
We are trying to integrate an accelerator driver with the code written in c++ with example code from twi sensor from the SDK 0.10 for the nRF51, which is written in c. Will...
Hi,
I am struck with the problem of GAT ERROR when I upload my application zip file through Nordic nRD ToolBox in Android.
These are my steps:
I load the S310...
