Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
Hi,
So i don't have any experience of working with nrf ble chips, but i was given nrf52 DK and i need to make it work as an iBeacon. So i got the dev board working without...
I'm planning to implement a mesh network, where each node (ble device) also acts as a scanner, detecting BLE advertise messages. The mesh network would then forward the advertisement...
I noted on the release notes for S110 v8 (DRGN-5556, NRFFOETT-986), that enabling/disabling blue_radio_notifications() while the Stack is not idle can cause an assert. Does...
I need something in excess of 5mA output drive. Is there likely to be any problem with connecting two or more GPIO pins in parallel(providing I use OUTSET and OUTCLR to ensure...
Hi,
I have created a project with Keil 5.15
The simply blink app works. Now I want to play with softdevice.
The only problem is... no matter what I do, my hex file always...
Hi ALl
I have permanent error on connect command {0x05, 0x0F, 0x3f, 0xff, 0x40, 0x00 }
When I use security option, with or without PassKey. Return message is 01-03-84...
hey,
so today I updated my NRF Tools... I guess i was using an old version before.
To test our prototypes we have a test fixture where the board is programmed at the...
I'm looking to maximize the throughput using Gazelle on the nRF51.
Assuming zero retransmissions, I believe the theoretical max should be (1/TimeslotPeriod)*PayloadSize...
There is some doubt about the nRF2401L+ RF matching circuit.From the article of <<Tuning_the_nFR24xx_matching_network.pdf>> ,it says "The balun-function is done by the 180...
