I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
I'm developing a BLE application where I want my slave/peripheral to sleep as much as possible to save power. I'm not sure how to set the connection parameters.
I'm looking to migrate from SDK 6.1 to SDK 9.0, using GCC and Eclipse. Any pointers would be welcome.
Also, I'm hoping to start using the OTA DFU. Once again, if there are...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
