Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I've tried to set up my own BLE project as an exercise in understanding what's going on. It's going okay, with the exception that the device isn't advertising the data that...
I write PWR_UP using SPI and then read the Reg <0>. but I am not getting what I wrote.
Step 1 : Power ON using 3V.
Step 2 : Delay for 1 Sec to get into POWER DOWN MODE...
Hello,
On my custom board, I'm receiving chunks of UART data, without flow control, at 115200bps. Sometimes (its quite frequent now... sometimes after 10 chunks, sometimes...
I'm working on a PC application (using nrf51-ble-driver_win_0.4.1 API) to connect a BLE device and discover BLE services.
Today, I'm tying to connect the Nordic dev kit...
When discovering services using nrf51-ble-driver_win_0.4.1 driver, some ID are received with type BLE_UUID_TYPE_UNKNOWN. So I assume they are 128bits. I then retrieve the...
I downloaded the BLE beacon app S110 v7.1.0 to a nRF51-DK board. The current measurement pins were attached to a 10 Ohm resistor.
I observed the AC-coupled voltage at one...
Hi. We've got a chip with a code QFACA10. I am trying to find out if there is the internal pull-down of SWD line or not. It seemed that adding an external pull-down had positive...
Hi all,
I want to know the effect on power consumption of pins input buffer on and off, does there are big differences between them?
Another question is, since there...
Hey everyone,
when i was trying to compile i got this error which says
._build\ble_app_bci.axf: Error: L6200E: Symbol SWI0_IRQHandler multiply defined (by nrf_notification_manager...
i have few question based on nordic i am using N51822.
1: does device goto sleep, while testing i see sometimes device gets automatically disconnected.
how can i solve...
Hi,
what would be a good option to create a BLE device like FLIC (flic.io).
i want to transmit only a few informations to the smartphone like 1,2,3,4 and the device shall...
Hi,
every time i try to call ble_bas_battery_level_update(&m_bas, 1); my application freeze and i can't get any response
Here is what i did:
1- copying ble_app_template_s110...
Hello folks
I have a custom PCB board with the attached layout diagram. I also have our firmware that was flashed on to the Nordic beacon kit and tested. I would like to...
Hello,
at the moment I try to add some more services to my BLE device. This goes wrong with err_code = 12 (NRF_ERROR_DATA_SIZE). With some search in the devZone I found...
