Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Two applications using the same softdevice, s110, blinky and beacon from the examples.
Flashing softdevice and beacon successfully.
Replacing beacon app by blinky successfully...
The bootloader in SDK 8.1.0 (at /nRF51_SDK_8.1.0 examples/dfu/bootloader) calls pstorate_register() twice. The first time as part of bootloader_init(), then on bootloader_dfu_start...
hi,
I have implemented a UART to receive network packets from another controller to send it over BLE.
UART config are: 8bits data, 9600 baud rate, no parity, HW flow...
Hello,
I am wondering wether I need to pass regulatory tests when I use the S130 Softdevice together with a 3rd party module such as the one offered by raytac ( www.raytac...
Hi,
So i don't have any experience of working with nrf ble chips, but i was given nrf52 DK and i need to make it work as an iBeacon. So i got the dev board working without...
I'm planning to implement a mesh network, where each node (ble device) also acts as a scanner, detecting BLE advertise messages. The mesh network would then forward the advertisement...
I noted on the release notes for S110 v8 (DRGN-5556, NRFFOETT-986), that enabling/disabling blue_radio_notifications() while the Stack is not idle can cause an assert. Does...
I need something in excess of 5mA output drive. Is there likely to be any problem with connecting two or more GPIO pins in parallel(providing I use OUTSET and OUTCLR to ensure...
Hi,
I have created a project with Keil 5.15
The simply blink app works. Now I want to play with softdevice.
The only problem is... no matter what I do, my hex file always...
Hi ALl
I have permanent error on connect command {0x05, 0x0F, 0x3f, 0xff, 0x40, 0x00 }
When I use security option, with or without PassKey. Return message is 01-03-84...
hey,
so today I updated my NRF Tools... I guess i was using an old version before.
To test our prototypes we have a test fixture where the board is programmed at the...
I'm looking to maximize the throughput using Gazelle on the nRF51.
Assuming zero retransmissions, I believe the theoretical max should be (1/TimeslotPeriod)*PayloadSize...
There is some doubt about the nRF2401L+ RF matching circuit.From the article of <<Tuning_the_nFR24xx_matching_network.pdf>> ,it says "The balun-function is done by the 180...
