I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I am working with nRF24LE1 and I use the Gazzell library. But I need a real time base. I have a chance, because I think Gazzell uses that resource. Is there any way I can...
Hello
I am using gazell on the nRF24LE1.
I would like to know some recommendations on how to estimate a consumption on the side of the device based on the times and repetitions...
Hi. I just recently started using nRF24L01+. I am trying to simulate MultiCeiver using 2 mcus and 2 nrfs.
PTX sends a message on all 6 pipes of the PRX. The problems start...
HI,
I look at nRF5 SDK doc about Gazell,see that 'the nrf_gzll_device_tx_info_t contains the num_channel_switches parameter which can be used by application to determine...
Hello
I am quite a beginner and have been trying to get it work for 2 weeks now.
I would like to merge these 2 example codes from nordic:
Shockburst TX example...
Hi everyone,
I want to use MasterEmulator.dll (2.1.13.14) in my own application (C#) for development. Then I realised that line
MasterEmulator mMasterEmulator = new...
I am using nRF52 and Raspberry Pi 3 (with BLE).
In the Raspberry Pi, I am using bluez.
I was attempting to connect with the NORDIC_BLINKY app but the message below was...
Hi, I wonder how to get the Nordic SDK-examples work with VisualGDB.
As I would like to read TWI sensor values a good point to start from are the Nordic examples.
But...
my project is used nrf51822 mcu, it contains SIM, when the mcu is reading SIM data, and at the same, I take out theSIM, and the 51822's pin which is link with SIM is can't...
Hi, Nordic
I use SDK12.1 with nRF52832, I found one issue:
if I do not program bootloader, nRFgo Studio can program app.
First, erase all flash, then program softdevice...
Hi Everone/Nodiac
I had tried so many threads and previous questions but not bale to get my answer so asking after two weeks.
I am willing to send a string from stm32f4...
Hello,
I currently working with the nRF52832 chip on a custom board. The external clock is a 32MHz clock with +/- 10 ppm. When I use nrf_delay_us or nrf_delay_ms the delay...
