Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
Hi,
I'm trespassing some code of nRF51 to nRF52 (s132, SDK 12.2.0) and I get an error when I try to call sd_ble_gatts_rw_authorize_reply. This is the code
case BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
I'm using the beacon example (SDK 12.2.0) which I've modified slightly so that a sensor output initiates advertising for 20 seconds with LED1 flashing accordingly. I want...
Hello I was working with the Flash Storage examples in the nordic github repo. I noticed that the FDS example while it has a IAR Workspace it does not have the associated...
Hi,
I am having trouble with buttonless DFU on my application. I am working on custom hardware on the nRF51822, SDK10.0.0, S130.
When I enter DFU from my application...
I'm working with pca10028.
Then gpiote interrupt is triggered twice.
Why is this happening?
And what is BUTTONx_EXT connected to PCAL6408A(U7) in schematics?
Hi,
I am new to nordic development. I have programmed segger program softdevice by s110_nrf51_8.0.0_softdevice.hex and program bootloader by dfu_dual_bank_ble_s110_pca10028...
My project is to communicate with the AD7780 via SPI.
Nrf is the master and AD7780 is slave. I am know implementing my solution referring to an example i found about SPI...
I'm trying to make the nRF51422xxAC advertise. Using Segger Embedded Studio.
I have this code: bpaste.net/.../f29f74986c10
On line 109, I have a breakpoint. At that...
I've followed the tutorial about setting the eclipse environement devzone.nordicsemi.com/.../
I've got every thing to work except the debugging, it stops every time at ...
Hello,
I am trying to set the nRF52 to power off and wake up on a momentary button push (scope measures momentary push logic low around 50ms-100ms). However, I am struggling...
