I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
Hi,
I'm thinking of using the NRF52 for an embedded wearable sensor application.
How much flash and Ram space can I expect to have remaining approx. for my application...
I'm a bit at a loss of how to voluntarily stop advertising: My related thread says I should call sd_ble_gap_adv_stop() , but when I do, no corresponding event is raised by...
To install micro-ecc, complete the following steps:
Install version 4.9-2015-q3-update of the GCC compiler toolchain for ARM. You can use ARM's Launchpad to find the toolchain...
Hello everyone,
I am currently porting a project from pstorage to FDS.
I am testing the functionalities of FDS including create, update and delete records and I am at...
Hello,
To reproduce this problem I use these steps:
Bond to NRF51822 using Android 6.0.1 and latest nRF Connect version;
After successful bond, connect to NRF51822;...
Hi,
We are using PPK board (PCA63511), we have followed the "PPK user guide" and installed all the necessary softwares, We have made the connections and switches option...
Hello everyone, I'm Dario.
I'm trying to work with a ble nano with nordic component. My target is to receive a string via serial periferial and sending it via bluetooth as...
I am a new engineer working with nRF52 and SDK 12 using Makefile project and arm-gcc. I wrote some simple code to try TWI Master and control a i2c slave device. My question...
Hello I just bought
SKYLAB bluetooth accelerometer sensor SKB360 bluetooth low energy nrf51822 bluetooth 4.0 low energy module
skylab.en.alibaba.com/.../SKYLAB_bluetooth_accelerometer_sensor_SKB360_bluetooth_low_energy_nrf51822_module_bluetooth_4_0_low_energy_module...
Hi,
Im trying to wake up from SYSTEM OFF using LPCOMP.
Im using the following code to power off:
nrf_drv_lpcomp_config_t config = NRF_DRV_LPCONF_DEFAULT_CONFIG;
...
Hi,
I am working on a Beacon application based on nRF52 DK and Eddystone protocol. So i am searching if there is already some examples/SDKs from nRF which supports both...
Looking for document or u tube to program nrf52832 using tag connect (6pin noleg) and nrf52 DK. Have the hex program and put it on the nrf582 dk. need to take to the next...
We have identified a possible transient fault condition in which a voltage in excess of VDD can be applied to an I/O of the nRF51. VDD is 3 V and the excess voltage would...
sdk_resources.h does not compile with c++ in SDK12.
The _cplusplus guard only begins if ESB_PRESENT is defined. The guard should either be moved above or below
#ifdef...
