Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
I'm stuck in the Puck Central Tutorial, I have the zip from GitHub but can't seem to get any project to open.
Completed OK:
I completed the Puck Toolchain and Location...
I am right that:
a) once started the watchdog, it is not possible to stop the watchdog from the application
b) once started the watchdog, it is not possible to reconfigure...
I have successfully gotten the DFU to work on the NRF51422 S310V2.2 softdevice. I can download blinky app via the nRF Toolbox DFU application and all works great, but when...
Hi.
I am new to this forum, and can be described as a programmer with very little embedded experience.
I have bought a nRF51822 BT SMART BEACON KIT, and are trying to...
Hello,
i would like to turn off a sensor completely when unused and thought of powering it through the GPIO of the Controller.
I wondered if it is recommended or do the...
We have updated multiple android phones to nRF Toolbox for BLE app and we are all getting "Unfortunately, nRF Toolbox has stopped." error message when opening the app. nRF...
Hi,
I want to get a notification when the BLE event is started, in order to start a timer just after.
How can I get that?
I want to clarify my question :
My board...
I use the NRF 24AP2E in my communications, and I need detect if the communication is good.
I active the RSSI message, but in scanning mode I don't receive byte 0x20 in Measurement...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
