Hello, I am encountering an issue while setting up an OpenThread Border Router (OTBR) using the following hardware: nRF52833 board (flashed with RCP firmware) nRF52840 board...
Hi
custom board using the nRF9160, toolchain version v2.6.0, mfw_v1.3.6.
Sorry I can't provide a decrypted modem trace, but I hope the screenshots are enough to show what...
Hi, I am working with nRF52 DK (52832), and the issue I am facing is that i am unable to increase the data size of data SPI -DMA can receive. Currently it is configured at...
Hello everyone,
I want to evaluate the power consumption in idle mode of the nrf9151 sip.
Environement:
nrf9151dk_rf9151_ns
nRF Connect SDK Toolchain v3.0.2
VScode...
I’m using SMP over UART to send the erase command ( {"slot": 1} ), and it only erases the application core image (image 0). I also have a network core image (image 1) present...
So i am currently referring this ticket and from that I get to know that when when setting parameters for create config (HCI_LE_CS_Create_Config) command for channel sounding...
I am trying to get the lowest possible power consumption for my Thread device, so I am experimenting with different configurations.
Currently I'm testing with SSED ( Synchronized...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
Referring to page 58 of the reference manual there is a ANAEN control signal that will contect a gpio pin to a corresponding analog input
I am using GPIO P0.01 -> AIN2...
I have started "playing" with the nRF51822 eval kit and the LED-Button example explained in the nAN-36. I wanted to know how is the UART port configured but I have not found...
Is it possible to count pulses with the 51822 from an external device in the range of 250-15.000 pulses pr. second, while the CPU is powered down (softdevice sleep)?
I...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi all,
i am new to nordic and I working on the project to scan/locate iBeacon by using nRF51822,
I can't found a related sample code on SDK 5.2.
Is there something I...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have built a board using a reference design for the USB dongle board for the NRF24LU1+. Now when I connect to the USB the system identifies the device as "nRF24LU1+ -F32...
Hi!
I just ordered nRF51822 and nRF8001 chipset from Digikey, not dev KIT. I want to develop product by ourself based on nRF51822 and nRF8001 chipset so I want to have all...
In s210 there are functions sd_flash_page_erase, sd_flash_protect, and sd_flash_write. There is no sd_flash_read.
How do I read from flash? I can write to is using sd_flash_write...