I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
As indicated in the PS, System On Mode idle draws only 2.6 uA.
Does this mean that if I install and active a timer interrupt, where the interrupt routine places the system...
Hi,
I am new to ARM development. We are thinking of ordering mkit for evaluating and developing a custom BLE service(profile) which sends data to BLE client (probably a...
Hello Everybody!
I have been working with BLE security and I have an issue with OOB setup.
I'm setting my nRF with the following:
m_sec_params.timeout = 30;
m_sec_params...
I was reading this press release:
http://www.nordicsemi.com/News/News-releases/Product-Related-News/Single-board-Bluetooth-Smart-Arduino-solution-is-low-cost-and-can-be...
Yo!
I'm very concerned by what I hear about Bluetooth Low Energy security. According to this guy , who presented a paper on the subject at a USENIX conference last year...
Any experiences about analog sensor LM35DZ? I used this example: main.c
The LM35 data sheet says it will operate from +4V to 30 V supply. I'm use supply only Vcc pretty...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I'm using API 2.1.3 and I'm having problems with SendData blocking forever at the end of a process. I placed access mutexes around each method call to the library, as well...
Dear Nordic Developer Zone,
I have modified the ble_conn_params.c file in order to be able to negotiate new connections speeds between IOS app and Nordic nRF51822 chip...
Hi,
Regarding the bond_info_store() routine, I am having issues where after several calls to this function (client pairing forget/reconnect), my p_bond gets corrupted. This...
Hi, I am developing a BLE application using SPI and TWI. (Using nRF51822)
This discussion is about my survey in development zone for future develop the TWI part.
I want...
I'm calling ble_bondmngr_bonded_centrals_store in response to BLE_GAP_EVT_DISCONNECTED as is the case in plenty of sample code, but when ble_bondmngr_bonded_centrals_store...
Hi Guys,
I have managed to get the BLE DFU demo service working fine (dual bank) on nRF51822 EK. I use a Linux Python program ( bitbucket.org/.../nrf51_dfu_linux) (with...
what is the detection speed, when the beacon
enters into a wall unit area? With their 868 beacon they can
detect in 0,2 seconds. Is the nRF51x22 in sleep mode and does it...
