I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
I have met return error below point when I try to upload Application Hex file with bootloader in nRFgo Studio Ver1.17.0.3211.
if (!(IS_WORD_SIZED(m_start_packet...
I am trying to get enhanced shockburst working with the nRF24LU and the nRF5188. I am using the nRF5188 as the transmitter and the nRF24LU as the receiver. I am using the...
hii...
i hv maufature_array of size 7 to advertise.... am facing a problem while advertising battery level service with dat... my code is lyk dis
uint32_t err_code;...
Hi !
Here my adv setting (slow interval) to advertise every seconds :
#define APP_ADV_INTERVAL_SLOW 0x0664 /** This value corresponds to 1022.5 ms).
#define APP_SLOW_ADV_TIMEOUT...
Just ordered another pair of beacon hardware and noted the nrf chip is now coated in black goop.
Curious as to what this is for, and the reasoning its been added to the...
Hello,
I have a master configured as "Bidirectional Master Channel" and a slave configured as "Bidirectional Slave Channel". Both talk to each other. When I start just the...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
I ran into this last night and curiously, James appears to have posted about it yesterday ( devzone.nordicsemi.com/.../trouble-with-system-halted,but-cannot-reset-nrf51822...
I am trying to get the Heart Rate example in the nRF51 SDK to work (found in ...nrf51822/board/nrf6310/ble/ble_app_hrs). It fails at line 338 in main.c (at the call sd_ble_gap_device_name_set...
I'm putting some bootloader and static config data in the customer section of the UICR and I accidentally wrote to 0x1001200 and worked just fine.
Looking closer, it seems...
Dears:
We will adopt nRF51822 for our project, and we want to confirm with you for the question as below:
Does nRF51822 support HCI command protocol through either...
Hello,
I do erase flash pages in my application I use the sdk api:
nrf_nvmc_page_erase(firstaddress);
nrf_nvmc_write_bytes(address, data, len);
but I did not found...
