Hi.
After 3 days I've finally got littleFS working on a custom nRF52840 board. I am using nRF connect SDK v2.9.0 which includes Zephyr v3.7.99 with some additional Nordic...
Hello, I hope you are well.
I created a new driver for an i2c accelerometer with 2 gpio interrupts, but it does not build properly. When calling `static const struct device...
Hello everyone,
I'm working in a ble project that use uart interface. When I sent string data in nrf connect app, the uart_event_handle is not called.
I started my project...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
nrf5340DK
NCS 3.0.0
if I use sample zephyr/samples/boards/nordic/system_off it works fine and i can wake from sw0 press. but if i move the sys_poweroff() call int a...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
I managed to compile the ble_app_uart on windows 8.1 with cygwin. I had to remove all abspath on the makefile, as launchpad gcc is not compatible with cygdrive notation.
...
Hi, I use the NUS most of the time.
(SDK 7.2 & S110 7.1 with IAR 7.1)
As you know, HID keyboard or mouse bond with centrals (smart phones).
After bonding, when using...
nRFgo was unable to read attach to the boards I have with the QFAABB parts, but reported QFAABA parts correctly and programmed them. nRFgo was at 1.21.02.
I updated to...
Hi,
I'd like to retain a value in RAM after any type of reset, including a watchdog timeout, so that I can read it back in the bootloader immediately after a reset.
...
Hello,
I followed the tutorial to use Eclipse GCC and both examples (blinky without softdevice and HRS with S110) work fine, i.e. I can build and flash them.
Now I try...
Hi,
First of all I appreciate the way nordic has put tutorials on the website for the newbies.
I am working with putting custom services in my code, and its working...
Hi everybody!!!
I am working on ANCS on NRF-DK51 (nrf51-sdk-9.0.0) and I get the disconnected reason 0x002A same as this topic . They said that to overcome this problem...
Hi,
I am using nRF52382 controller and we are planning to put RTOS on it. Is it possible to use the same RTC for system ticks as well as to set current time?
In the Example "ble_app_cts_c_s132_pca10040 " messages are send to the UART output, by default the UART Hardware Flow control is active. I would like to disable the Hardware...
We have designed a product using Nordic's nRF51822 and will be selling into Korea and Taiwan market.
Recently, there is a new requirement for us to provide antenna radiated...
Hi
I started form the lbs example to build my application. I have now the following problem:
apparently the button_event_handler is only triggered when the device is connected...
Hi,
I have searched the forum, but still I cannot find answer to my question. I designed my custom board for nRF51422 and want to work with ANT (softdevice 210) (I have...
Hello everyone
i want to create button fucntion press the button for 3 seconds and then it has to start advertsing but i have excuted the button fucntion but it si showing...
