I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I am using the nRF51 transmitter_pca10028 example to try to communicate with legacy systems using nRF2401A.
I could achieve nRF51 TX to nRF24 RX successfully...
I would like to burst out 12 packets of 64 bytes and then go into RX mode immediately after for a single payload, followed by another round of transmissions. Is there a shortcut...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
Hello,
My device is based on nRF51822 SD110 v8.0. Softdevice is enabled, but no BT functionality used. I measure 2 different voltages with ADC each second with two channels...
I'm writing code for PCA10040 basing on UART/NUS example. There are no big changes: different UUIDs and just one characteristic for both reading and writing. I can connect...
This is a follow-up question from devzone.nordicsemi.com/.../
I finally got passkey support to work on ble_app_uart but don't quite understand the changes made to the code...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:
www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png
I add required...
