Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
Hi everyone, I don't have the nRF51822 yet, but still want to get familiar with it as much as possible before I get to buy it. I was looking for a description of the functions...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Has any managed to connect a Windows Phone 8.1 device to NRF51?
BLE is "definitely" supported on Nokia Lumia:
Nokia Support
But I am unable to pair with either SD 5.1...
I'm working with a custom hardware board made by hand which works properly, but since we make a batch with a pick and place machine, something seems to be wrong with the board...
I am trying to use the S110 v7.0.3 with a nRF51822 QFABA0 chip. I am using the hrs example from the SDK v5.2.0 ( I have changed the IROM address to 0x15000). I've got an error...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Dear Nordic,
I would like to implement on server side Private Resolvable address according to specs. For that I need to get the IRK that has been sent to client (central...
Can't seem to find the proper sdbc file and pack for the newest version of 51422_S210_256k for Keil 5 on either Keils site nor Nordic's. Called Keil and was told that Nordic...
In Nordic\nrf51822\Board\pca10001\s110\ble_app_hrs project,when I add somting into this project but the now that I add dose not work!!?
//this is buzee_gpiote_init()
static...
Hi,
I am working on proximity solution app and I have to implement link loss and immediate alert service but don't know how implement it as I am a learner in this technology...
Hello
I think my question is pretty simple but I would like to clarify this topic, please:
I have read in other threads in this forum that " bonding should eliminate the...
Hello,
Actually, I am evaluating the nRF51822 using the EK. I have some questions as follows:
1- Is the S120 an enhanced version of the S110, and what is the real difference...
I use P0.2 as a wake-up pin, when the system into a deep sleep, I connected a High Voltage in the P0.2, it can wake up, but if I connected a High Voltage in the P0.2 always...
