Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hello,
I have some problem with a specific phone. I try to connect with the nrf52832 using samsung S3 with android version 5.1, the connection takes 20 - 50 seconds and...
Hi,
I am very new to nrf51822 controller. I Used STM32 cortex controller's.
I want to know basic hardware which are the require to start nrf51822 working and programming...
The example nRF51-DK gerbers have solder mask on the PCB antenna. But for the nRF24L01+ EK gerbers, the PCB antenna has the solder mask removed partially, along the length...
Hi,
I downloaded the nrF5 SDK V12.2 from:
www.nordicsemi.com/.../nRF5-SDK
after unzip, I could see the SDCard library under "\nRF5_SDK_12.2.0_f012efa\components\libraries...
Following III. Example code and Enabling whitelisting ,
I try to connect to the "nRF52 DK" board with a whitelist (Android BLE device address),
but I've never connected...
1、I use SDK9.0 ANCS project, the position is as follows:
SDK9.0\examples\ble_peripheral\ble_app_ancs_c\pca10028\s110\arm4
2、I need a project which is contained with...
hello there,
i am giving external supply to nrf51. my external supply is usb 3.3 v. but when i connect it with nordic and then if i check it on multimeter , it shows me...
Hi all,
Does anyone know how much current is meant to be drawn to discover nearby devices? I guess, in other words, how much current is drawn to put the nRF51822 in discovery...
Hi Sir,
I have a NRF 51822 board & MPU 9250 sensor.
I want to read YAW,PITCH,ROLL,ACC_X,ACC_Y,ACC_Z,GX,GY,GZ,MX,MY,MZ values from MPU Sensor.
Could you please share...
Hi All,
Continuing on with my project: a custom board containing nRF52 + ECG front end.
Successfully integrates SPI functionality; need 2 more interfaces:
32...
Previously you recommended using S132 v4.0.0 2. alpha release to get more than 8 central connections. As far as I know this revision doesn't implement Bluetooth 5.0 protocol...
Hi,
I have written a code which transmits data over BLE.
The board was getting reset.
What we changed is instead of sending application data we sent the RESETREAS register...
Hi,
I'm trying to change the MAC address of nrf52, using softdevice s132_nrf52_3.1.0 but we dont have sd_ble_gap_address_get() and sd_ble_gap_address_set() APIs in "ble_gap...
We are having a random current leakage problem with our nRF51822 based board. Normally, our board and the application consumes around 10 uA of current. However, too often...
For example, I have the following code:
bool interruptFlag;
void interruptHanler(void)
{
interruptFlag = true;
}
void main(void)
{
while (true)
{
if (interruptFlag...
