I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
My target is to create prototype of ANT application with the continuous scan mode. The application works as ANT slave. It is expected to monitor the message boardcast...
Hi,
I am using arduino to sample sensor and it sends out the value to the digital pin. I want to read this digital value using nrf51dk. Is there any example using digital...
Hi Nordic Tech support team,
I have some questions about nrf51822 dfu OTA.
Nrf51822 application code can't be more than 144K，however ，my application code have 196K because...
we follow the nRF51_Series_Reference_manual v3.0, set the master SPI clock to 8M. but found when in mode 0, the MOSI change near at SCLK rise edge, not in fall edge.
our...
This should have been a very simple question. I don't want to use CTS/RTS flow control signals with my UART-USB-converter ("FTDI chip"). For that case, the document says ...
I want to highlight some items in RTT Viewer
So I tried the color control, but didn't work
This is my code.
SEGGER_RTT_printf(0, "%s[Mutex error:%u]\n%s", RTT_CTRL_BG_BRIGHT_RED...
Hello.
I am trying to port BLE serialization code to a host MCU, to say STM32F4.
I am looking through porting documentation (BTW, it is quite well documented. Well done...
According to Microsoft's instruction on HID touch device, msdn.microsoft.com/.../dn672271(v=vs.85).aspx , a HID touch device should create a report (descriptor) as below,...
Hi,
I am having a 324 byte,a 420 bytes of array stored in flash,now i am updating these array with 360 bytes. in fds_event_handler in the case FDS_EVT_WRITE i am reading...
Hi,
I'm looking for an example which combines FreeRTOS, BLE and ADC on nrf52 board(10040).
I'm able to have FreeRTOS with BLE, FreeRTOS with ADC but not everything together...
Hi,
I've read a lot of question on the forum, but I'm a lit bit confused about what I have to do to use one static passkey on the central and peripherical device. In my...
Hi There,
I'm having problems with my hardware timer appearing to stop counting or not being cleared via a short when the timer interrupt is executing.
In my application...
Hey!
I want to use the nrf51 BLE-module in some special environment.
It should be able to work with bluetooth and in addition to it with some other RF protocol (Gazell...
