Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Consider a situation where a BLE peripheral (nRF51822, S110) and an Android device are being used. Assume the buffers of the BLE stacks are empty.
Is it possible that the...
I have a BLE device that listens for a connection - upon opening a connection with a smartphone and switching advertising status to non-connectible - it receives some data...
I use nRF51 DK and soft device s130.
I nedd to add a file ("app_uart_fifo.c") in the example of multilink central, after i add the file i build the proyect but the files...
To confirm this link text .
I want to know how to run raspbian-kernel v3.17.4 .
Is there rasbian image including kernel v3.17.4 in rasbian images site ?
Hello,
There have been some questions on the forum regarding the DFU and it's zero value for the application CRC. However, none of them seem to address this question so...
Regarding the radio peripheral, I stumbled upon these 2 properties and have no idea what they are for.
What's access address? And what is a channel? Shouldn't there be...
I am runing ble_connectivity example with simple_uart instead of app_uart was not working unable to scan not getting advertisement reports.
Its been working with PCA10001...
Hi,
I have a pretty simple problem but I can't get it right. This is what I want to do:
T=000, PIN_x = 0
T=004, PIN_x = 1
T=100, call a routine
T=543, Start over...
Hi,
In the BLE_UART example code posted here , I noticed a discrepancy with the SD 3.0 migration document, SDK12, and the example code.
In stock SDK 12.1.0, ble_stack_handler_types...
Hello everyone, i need some help and suggestions in understanding what is exactly happening. I have read a lot about bugs and workarounds in pstorage and now i actually don...
Hi, when reading radio transmitter peripheral example, I got stuck a bit on radio_configure(). I got stuck because I can only get some brief from the corresponding .h file...
i m using nrf51.... first i have call WFI(); and device goes to sleep mode...and when press any switch on gpio so, wack-up again...so, may i know that.. how many way for wack...
i m using gcc toochain setup in windows for pca10028 devlopment kit... and load BLE_UART code inside it... and now i m add onother rtc code inside it.. but it's not work....
main.c hello sir.. i m place rtc example code inside of ble_uart code .. and i m using gcc tool chain setup for pca10028 bord... code complile sucsessfully... code not work...
Hello all,
I want to use a single bank bootloader with the ISP1302 Module (nRF51822 Chip) and S110 (V8) Soft Device, SDK 10, for application update
Can I use the BLE...
