Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi everyone,
In my low power application , I use PORT EVENT to detect the interrupts of my two pins.
when I use only one pin interrupt, it's working well .
But with two...
Dear All,
We are implementing 8 Pheripheral Nodes and one central node with S110 and S120 respectively.
We have our custom board with us we are able to connect the pheripheral...
Hi
I want to run RAM retention sample example with sd_app_evt_wait(void) .is it possible?
is it require soft device to load first?
I have included S110 soft device of...
Hello Nordic team,
are there documentation about the MTTF (Mean Time To Failure) Value of the NRF51822?
For more details please see the EN 13849-1. We need this information...
Hi
I want to operate nrf51 in various power modes available like low power mode, constant latency mode system idle mode and so on.my questions are as follows:
...
Hi,
I am using the following statements for send a string data over BLE.
static uint8_t Name3[BLE_NUS_MAX_DATA_LEN]= "xxxxxxxx";
err_code = ble_nus_string_send(&m_nus...
Hi.
I have interesting UART problem in Ubuntu. The multilink example only outputs one character at time, and line change doesn't change line. However if I flash another...
Hi,
We are using 52832 to developing.We need DSP to finish the arithmetic.
Can you tell me how to use the DSP on 52832 ? Do you have same examples?
These algorithms...
I have an nRF52 dev board and I'm trying to build and download some of the example programs.
The example files were downloaded using the Pack Installer in Keil MDK-Lite....
Is there any way that can allow the user to advertise a sine wave for example over a specific channel or over the three Radio channels ?
I am using S130 and Nordic SDK 8...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
