I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi
I can't seem to find this in the datasheets, what is the active current consumption of the nRF52832 chip, I'm interested in the maximum expected current consumption...
Hi!
I want to connect a nrf51 dk with a beacon and I'm using the UUID to make the connection. In the beacon code I define the UUID in this way:
ble_uuid_t adv_uuids...
I use nrf52832 with softdevice s132_nrf52_1.0.0-3.alpha for a ble application on own pcb.
first I'm not sur of adresse to use for iROM and iRAM areas. I've this parameters...
//Hi Everyone!
//I am programming a nRF52832 through the SDW interface and am having trouble answering some questions.
//So, first off is simply checking my understanding...
I have a recent dev board and am using SDK11 with gcc.
I can build and flash OK
The blinky sketch runs
However, when I load up examples/ble_peripheral/ble_app_proximity...
We bought the Beacon Kit from Nordic. I'm trying to use the firmware code on a similiar beacon board based on same Nordic Nrf51822. The board has same button and led pins...
The release notes for the S132 V2.0.0.0 SoftDevice indicate it's only compatible with silicon revisions C and 1.
I have several PCBAs that have the rev B silicon. Will...
Hi guys
First of all, I know nRFgo can be very convenient for application encryption, but in order to improve the mass production efficiency,I merged the application code...
Hi!
Goal: I want to send as much data as possible using CoAP.
I have connected a nRF52 (IoT-DK) to a Raspberry Pi using BLE and 6LoWPAN. The nRF52 is running the CoAP...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
With the latest nrfjprog from Nordic and latest J-Link software from Segger, I am still getting the error below.
$ nrfjprog -v
ERROR: JLinkARM DLL version used is too...
I am working on the ble mesh using nrf51822. I am able to read the mesh values using the nrf master control panel android software. But we want to make an android software...
the priority of my custom thread is lowest priority. but it's not possible to call hvx function.
in ble_app_hrs_freertos example,
a sd_ble_gatts_hvx function is called...
