Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Dear All.
I tried to test and evaluate LoRaWAN stack on Zephyr, without success. I will need more time to debug what is happening by the logic analyzer. Meantime I attached...
Hello,
I am using a nrf Development kit and I have it plugged in into a mac laptop. It works fine, but I keep getting the message that says:
Disk Not Ejected Properly...
So I need to decrypt a single 16 byte block of data using AES128 and a pre-shared key on the above SoCs. But PSA doesn't seem to work (I'm currently working using the nRF52DK...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi team,
I'm using the NRF54L15DK board with NCS SDK v2.9.0.
I'm trying to include the B0 bootloader along with the MCUBOOT and application.
I'm wanted to customize...
As subject, the key is using prj.conf, compilation errors will occur, if do not use prj.conf, c ompilation pass but 54L15 not work(no logs aft pwer on). Is fast pair(locator...
Hi, I am currently migrating my project from nRF Connect SDK v2.5.3 to v2.9.0 / sysbuild.
Unfortunately, my devicetree configuration for a mcp2515 CAN interface is not accepted...
Hi, Nordic team
we want to develop indoor tracking system using nordic soc chip we saw some sample codes from your nordic sdk 2.9.0 , we need any research papers or documentation...
While experimenting with the v2.6.0 set of matter examples, it was noticed by an associate that the LightSwitch example doesn't seem to want to connect to any networks. This...
I am using NCS v2.9.1 and trying to enable a bootloader chain with NSIB and MCUboot. The regular setup works fine, however if I try to enable the minimal configuration, I...
Hello, just like the title indicated, I need help with setting up the nRF21540 EK with the nRF9160 DK.
For my application, since the nRF9160 DK has the nRF52840 on it, I...
Sorry for the inconvenience!
I have downloaded V2.8.0 nRF SDK, and I use this command to build light bulb project:
west build -p always --build-dir nrf/samples/matter...
Hi everyone,
I’m working on a project involving the nRF7002DK, where I’m trying to combine two separately working applications:
A TinyML CIFAR-10 image classification...
I am attempting to configure and build the Asset Tracker v2 for my Actinius Icarus v2 board.but the build is failing.
Setup:
nRF Connect SDK v 2.9.0
Board target:...
