I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi all.
I am making a PCB for nRF51822. My PCB need is to talk with iPhone for BLE Proximity application. Also I need to control a LED from iPhone. And I need to get low...
In short: Is it feasible to use RSSI values when tuning the antenna?
I have a custom board with an nRF51422 on which I have designed the RF part to be as much as possibly...
Any suggestions for handling a bricked custom board?
I'm pretty sure I know where the problem is in my code, but now I can't reprogram the board. I did have this happen...
Hi, I'm developing an BLE application using nrf51822.
I have a BLE security issue to discuss.
(Actually I don't have much network security background...)
In our application...
I'm using PCA100001 board with pure-gcc Makefile and s110_nrf51822_5.2.1_softdevice.
And I'm writing simple code customizing s110 samples like below:
static void ble_stack_init...
Hi
Does the NRF51822 support ANT and where would be a good place to understand how to implement ANT ? I also want to know where I can get more information regarding the...
Hello community, first time posting a question so please try and forgive any future mistakes.
anyways im new to using the keil IDE and am have some problems. I have dug...
I am using pca10001 board and started my development from nrf6310/s110/ble_app_hids_keyboard.
SDK version is 6.0.0. I have successfully tested my device with (MCP) Master...
Hi,
I am very new to BlueTooth technology. Currently i'm testing the nRF51822 evaluation kit to see if the BLE module can be used for a specific project. I've tried several...
I have a schematic in which Balun is connected as a matching network to Ant1&Ant2 pins making the output impedance 50 ohms. Now i want to connect an Antennae to it which is...
Pages 51 and 53 of the nRF8001 Product Specification (v1.2) show a reference design for a balun network in which capacitor C4 is listed with a value of "N/C". The component...
Just in case no one has ever given any feedback WRT Eclipse, Id like to be the first. My experience is using it with all the features for a NRF51822 project, and it kind of...
Seeing, that the nRF51822 was specified to operate with a 16 MHz crystal or oscillator. Is that also the clock what the Cortex-M0 core runs or is there a PLL to increase the...
Dear Support Team,
I'm working on a BLE application and the most stuff works well but now I had a spurious application crash at "src\ll_lm.s0.c: 1038". Could you please...
Hi There,
We referancing the PCA10000 for antenna circuit design. We are going to use 0.8mm FR4 PCB however we couldnt find out the Thickness of copper conductor. And it...
