I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I am trying to setup a couple systems to use the Nordic rf sniffer. I have a pca10000, a pca10001 ver 2.0, a pca10001 ver 2.1 and a pca10031.
I loaded all with the rf sniffer...
Hello,
I am sending below setup packet to nRF8001, and i don't get any response form nRF8001. ACI as such works fine, i tried sending diff commands and able to receive...
Hello,
I am using Lenovo (late 2015 release) with android 4.4.4.
Got my nRF51822 Bluetoot Smart Beacon kit and downloaded the applications that are available on Playstore...
I have some very basic code that does not appear to be executing correctly.
There are two versions of code that I would think should have the same result. They do not,...
I am having trouble with setting priority of ADC_IRQn.
void ADC_init(void)
{
nrf_adc_config_t nrf_adc_config;
nrf_adc_config.reference = NRF_ADC_CONFIG_REF_VBG;
nrf_adc_config...
I'm using the nRF52-DK (SDK11.0.0+s132) and added in some example code from the RTC example (the RTC2 tick interrupt with prescaler=0 to toggle a GPIO) to the ble_hrs example...
Hi there!
I don't know much about FCC, UL, CE certification and want to learn. I am using the blend micro module which uses nrf8001 chip in my project. How do I get my...
Hi, i've just started to use the nRF8001, so forgive me if this is an obvious problem.
i'm using the nRF8001 with a microchip PIC processor.
i'm using the ace_tl_demo...
Hi,
I have read ANT Message protocol and Usage and tried to implement shared channel according to section 8.2. I am using nrf51422 and S210 and SDK 10.0.0
My master...
I'm trying to use TDD for my development of a BLE peripheral application, but I'm running into some problems. I'm using Ceedling, CMock, and Unity for my TDD environment,...
I'm trying to scan beacons. This is what I added to the example ble_app_uart_c :
case BLE_GAP_EVT_ADV_REPORT:
{
const ble_gap_evt_adv_report_t * p_adv_report = &p_gap_evt...
Hi all,
I have a problem in architecture of my application based on SD132v3 SDK12. It should interact with an iOS device as a peripheral and receive some data to display...
Hi,
I am using NRF51822 and SDK11 with S130. I have enabled WDT with 2000 as reload value as I'm using 1 second timer. But I want to immediately reset when a certain condition...
